Eğitimler
EsploraTable
Bu örnek, Esplora'nın ivmeölçerinden veri toplama ve bilgisayarınızla grafik oluşturma görevini basitleştirir. Esplora, ivmeölçerin durumu hakkında bağlı bir bilgisayara tuş basımı gönderir. Bir elektronik tablo uygulaması açarsanız, verileri ivmeölçerden günlüğe kaydedebilirsiniz.
Veri kaydını başlatmak ve durdurmak için aşağı düğmesine basın. Esplora'nın LED'i günlüklemenin durumunu gösterecektir. Kaydırma çubuğu örnekleme aralığını ayarlamak için kullanılır.
Gerekli Donanım
- Arduino Esplora
Devre
Bu örnek için yalnızca Arduino Esplora'nız gereklidir.
Esplora veri kaydı kurulumu
Kod
Bu örnekte, Esplora bir klavye görevi görür; aşağı düğmesine bastığınızda, bağlı bir bilgisayara karakter gönderir.
Bilgisayara gönderilen karakterler e-tablonun satırlarına ve sütunlarına sığacak şekilde biçimlendirilir. Elektronik tablonun her satırı bir zaman damgası ve 3 ivmeölçer ekseni okuması içerecektir.
Numune almaya başlamak için aşağı yön düğmesine basın. Bu, bilgisayarla klavye olarak iletişimi başlatır. Doğrusal potansiyometrenin konumunu değiştirmek, örneklerin ivmeölçerden okunma ve bilgisayara yazma hızını değiştirecektir.
Esplora hazır olduğunda RGB ışığı mavidir, ancak veri göndermez. Aşağı düğmesine basıldığında LED yeşile döner. Esplora sperads sayfasına numune gönderirken LED kırmızıya döner.
Düğmeye tekrar tıklanması Esplora'nın veri göndermesini durduracaktır.
/*
Esplora Table
Acts like a keyboard that prints sensor
data in a table-like text, row by row.
At startup, it does nothing. It waits for you to open a
spreadsheet (e.g. Google Drive spreadsheet) so it can write
data. By pressing Switch 1, it starts printing the table
headers and the first row of data. It waits a bit, then it
will print another row, and so on.
The amount of time between each row is determined by the slider.
If put to full left, the sketch will wait 10 seconds; at
full right position, it will wait 5 minutes. An intermediate
position will make the sketch wait for some time in-between.
Clicking the Switch 1 at any time will stop the logging.
The color LED shows what the sketch is doing:
blue = idle, waiting for you to press Switch 1 to start logging
green = active; will print soon
red = printing data to the PC
Created on 22 november 2012
By Enrico Gueli <enrico.gueli@gmail.com>
modified 24 Nov 2012
by Tom Igoe
*/
#include <Esplora.h>
/*
* this variable tells if the data-logging is currently active.
*/
bool active = false;
/*
* this variable holds the time in the future when the sketch
* will "sample" the data (sampling is the act of reading some
* input at a known time). This variable is checked continuously
* against millis() to know when it's time to sample.
*/
unsigned long nextSampleAt = 0;
/*
* This variable just holds the millis() value at the time the
* logging was activated. This is needed to enter the correct
* value in the "Time" column in the printed table.
*/
unsigned long startedAt = 0;
/*
* when the "active" variable is set to true, the same is done
* with this variable. This is needed because the code that does
* the "just-after-activation" stuff is run some time later than
* the code that says "be active now".
*/
bool justActivated = false;
/*
* this variable holds the last sensed status of the switch press
* button. If the code sees a difference between the value of
* this variable and the current status of the switch, it means
* that the button was either pressed or released.
*/
bool lastStartBtn = HIGH;
/*
* Initialization code. The virtual USB keyboard must be
* initialized; the Serial class is needed just for debugging.
*/
void setup() {
Keyboard.begin();
Serial.begin(9600);
}
/*
* This code is run continuously.
*/
void loop() {
/*
* note: we don't use Arduino's delay() here, because we can't
* normally do anything while delaying. Our own version lets us
* check for button presses often enough to not miss any event.
*/
activeDelay(50);
/*
* the justActivated variable may be set to true in the
* checkSwitchPress() function. Here we check its status to
* print the table headers and configure what's needed to.
*/
if (justActivated == true) {
justActivated = false; // do this just once
printHeaders();
// do next sampling ASAP
nextSampleAt = startedAt = millis();
}
if (active == true) {
if (nextSampleAt < millis()) {
// it's time to sample!
int slider = Esplora.readSlider();
// the row below maps the slider position to a range between
// 10 and 290 seconds.
int sampleInterval = map(slider, 0, 1023, 10, 290);
nextSampleAt = millis() + sampleInterval * 1000;
logAndPrint();
}
// let the RGB led blink green once per second, for 200ms.
unsigned int ms = millis() % 1000;
if (ms < 200) {
Esplora.writeGreen(50);
} else {
Esplora.writeGreen(0);
}
Esplora.writeBlue(0);
} else
// while not active, keep a reassuring blue color coming
// from the Esplora...
{
Esplora.writeBlue(20);
}
}
/*
* Print the table headers.
*/
void printHeaders() {
Keyboard.print("Time");
Keyboard.write(KEY_TAB);
activeDelay(300); // Some spreadsheets are slow, e.g. Google
// Drive that wants to save every edit.
Keyboard.print("Accel X");
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print("Accel Y");
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print("Accel Z");
Keyboard.println();
activeDelay(300);
}
void logAndPrint() {
// do all the samplings at once, because keystrokes have delays
unsigned long timeSecs = (millis() - startedAt) / 1000;
int xAxis = Esplora.readAccelerometer(X_AXIS);
int yAxis = Esplora.readAccelerometer(Y_AXIS);
int zAxis = Esplora.readAccelerometer(Z_AXIS);
Esplora.writeRed(100);
Keyboard.print(timeSecs);
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print(xAxis);
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print(yAxis);
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print(zAxis);
Keyboard.println();
activeDelay(300);
Keyboard.write(KEY_HOME);
Esplora.writeRed(0);
}
/**
* Similar to delay(), but allows the program to do something else
* in the meanwhile. In particular, it calls checkSwitchPress().
* Note 1: it may wait longer than the specified amount, not less;
* Note 2: beware of data synchronization issues, e.g. if the
* activeDelay() function alters some variables used by the
* caller of this function.
*/
void activeDelay(unsigned long amount) {
unsigned long at = millis() + amount;
while (millis() < at) {
checkSwitchPress();
}
}
/*
* This function reads the status of the switch; if it sees that
* it was pressed, toggles the status of the "active" variable.
* If it's set to true, also the justActivated variable is set to
* true, so the loop() function above can do the right things.
* This function should be called as often as possible and do as
* little as possible, because it can be called while another
* function is running.
*/
void checkSwitchPress() {
bool startBtn = Esplora.readButton(SWITCH_DOWN);
if (startBtn != lastStartBtn) {
if (startBtn == HIGH) { // button released
active = !active;
if (active) {
justActivated = true;
}
}
lastStartBtn = startBtn;
}
}
Esplora Table
Acts like a keyboard that prints sensor
data in a table-like text, row by row.
At startup, it does nothing. It waits for you to open a
spreadsheet (e.g. Google Drive spreadsheet) so it can write
data. By pressing Switch 1, it starts printing the table
headers and the first row of data. It waits a bit, then it
will print another row, and so on.
The amount of time between each row is determined by the slider.
If put to full left, the sketch will wait 10 seconds; at
full right position, it will wait 5 minutes. An intermediate
position will make the sketch wait for some time in-between.
Clicking the Switch 1 at any time will stop the logging.
The color LED shows what the sketch is doing:
blue = idle, waiting for you to press Switch 1 to start logging
green = active; will print soon
red = printing data to the PC
Created on 22 november 2012
By Enrico Gueli <enrico.gueli@gmail.com>
modified 24 Nov 2012
by Tom Igoe
*/
#include <Esplora.h>
/*
* this variable tells if the data-logging is currently active.
*/
bool active = false;
/*
* this variable holds the time in the future when the sketch
* will "sample" the data (sampling is the act of reading some
* input at a known time). This variable is checked continuously
* against millis() to know when it's time to sample.
*/
unsigned long nextSampleAt = 0;
/*
* This variable just holds the millis() value at the time the
* logging was activated. This is needed to enter the correct
* value in the "Time" column in the printed table.
*/
unsigned long startedAt = 0;
/*
* when the "active" variable is set to true, the same is done
* with this variable. This is needed because the code that does
* the "just-after-activation" stuff is run some time later than
* the code that says "be active now".
*/
bool justActivated = false;
/*
* this variable holds the last sensed status of the switch press
* button. If the code sees a difference between the value of
* this variable and the current status of the switch, it means
* that the button was either pressed or released.
*/
bool lastStartBtn = HIGH;
/*
* Initialization code. The virtual USB keyboard must be
* initialized; the Serial class is needed just for debugging.
*/
void setup() {
Keyboard.begin();
Serial.begin(9600);
}
/*
* This code is run continuously.
*/
void loop() {
/*
* note: we don't use Arduino's delay() here, because we can't
* normally do anything while delaying. Our own version lets us
* check for button presses often enough to not miss any event.
*/
activeDelay(50);
/*
* the justActivated variable may be set to true in the
* checkSwitchPress() function. Here we check its status to
* print the table headers and configure what's needed to.
*/
if (justActivated == true) {
justActivated = false; // do this just once
printHeaders();
// do next sampling ASAP
nextSampleAt = startedAt = millis();
}
if (active == true) {
if (nextSampleAt < millis()) {
// it's time to sample!
int slider = Esplora.readSlider();
// the row below maps the slider position to a range between
// 10 and 290 seconds.
int sampleInterval = map(slider, 0, 1023, 10, 290);
nextSampleAt = millis() + sampleInterval * 1000;
logAndPrint();
}
// let the RGB led blink green once per second, for 200ms.
unsigned int ms = millis() % 1000;
if (ms < 200) {
Esplora.writeGreen(50);
} else {
Esplora.writeGreen(0);
}
Esplora.writeBlue(0);
} else
// while not active, keep a reassuring blue color coming
// from the Esplora...
{
Esplora.writeBlue(20);
}
}
/*
* Print the table headers.
*/
void printHeaders() {
Keyboard.print("Time");
Keyboard.write(KEY_TAB);
activeDelay(300); // Some spreadsheets are slow, e.g. Google
// Drive that wants to save every edit.
Keyboard.print("Accel X");
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print("Accel Y");
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print("Accel Z");
Keyboard.println();
activeDelay(300);
}
void logAndPrint() {
// do all the samplings at once, because keystrokes have delays
unsigned long timeSecs = (millis() - startedAt) / 1000;
int xAxis = Esplora.readAccelerometer(X_AXIS);
int yAxis = Esplora.readAccelerometer(Y_AXIS);
int zAxis = Esplora.readAccelerometer(Z_AXIS);
Esplora.writeRed(100);
Keyboard.print(timeSecs);
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print(xAxis);
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print(yAxis);
Keyboard.write(KEY_TAB);
activeDelay(300);
Keyboard.print(zAxis);
Keyboard.println();
activeDelay(300);
Keyboard.write(KEY_HOME);
Esplora.writeRed(0);
}
/**
* Similar to delay(), but allows the program to do something else
* in the meanwhile. In particular, it calls checkSwitchPress().
* Note 1: it may wait longer than the specified amount, not less;
* Note 2: beware of data synchronization issues, e.g. if the
* activeDelay() function alters some variables used by the
* caller of this function.
*/
void activeDelay(unsigned long amount) {
unsigned long at = millis() + amount;
while (millis() < at) {
checkSwitchPress();
}
}
/*
* This function reads the status of the switch; if it sees that
* it was pressed, toggles the status of the "active" variable.
* If it's set to true, also the justActivated variable is set to
* true, so the loop() function above can do the right things.
* This function should be called as often as possible and do as
* little as possible, because it can be called while another
* function is running.
*/
void checkSwitchPress() {
bool startBtn = Esplora.readButton(SWITCH_DOWN);
if (startBtn != lastStartBtn) {
if (startBtn == HIGH) { // button released
active = !active;
if (active) {
justActivated = true;
}
}
lastStartBtn = startBtn;
}
}
[Kodu Al]